Search Results for ‘bumper’

Its always bothered me that where it says Patriot on the back doesn’t stand out. I decided to fill in the lettering with black duplicolor bumper and trim paint after a failed attempt with plasti dip.

Ive been looking around everywhere and i cant seem to find off road bumpers that match the trim of the patriot and increace the approach angle and at suport for awinch and or light bar any ideas on what fits?

07-10 Jeep Patriot Rear Bumper-Trim Plate 1CR08TZZAB New OEM (Open Box) Part w/light scratches, two sided tape on back... $49.00 + $9.00 shipping to USA addresses... Length 48" Height 5 1/2" ___________________SOLD!!!_______________________

I came to my parking lot after work to notice a scuff mark and a indent on my jeep. it's on the bumper but on the side. right in front of the wheel but not on the front. is there any way to repair this pretty easily? i can buff out the scuff but the indent i want to try to repair. thoughts...

I made a couple posts a while ago about wireless versus wired and decided to go with wired. It was a two man job (especially to run the wire) due to the fact that I had never ran wire before and the lights came with absolutely no instructions or diagram... The lights are ProMaxx brand and were...

I am wanting some lights for my new brush guard and saw the Warn Lights W650D-HID on Rocky-road.com (http://www.rocky-road.com/warn-lights-w650D.html) for less than $140 and they are wireless. Has anyone purchased these? How well do they work and are you satisfied? How was the install? If not...

Here is my build. I bought the 2010 Patriot Limited about a year ago and have been making upgrades and modifications to it for the past 4 months or so. Here is how it started and where the project stands today. The day I bought it! [/URL][/IMG] 1st upgrade was the roof rack and a long road...

I made a post not too long ago about trying to find a brush guard for the Pat but the shipping cost more than the guard and put the total well over $500. I decided to contact some local fabricators and have them make me a bolt on brush guard with some what of a stinger bar. I attached some...

I have been doing some research and thinking about purchasing the RRO level 2 bumper mount/brush guard for about $500... The hesitation I have is that I am wanting a full front brush guard that will protect the grill, most of the plastic fascia as well as the head lights. I found several old...

I'm returning the jeep back to stock so all my parts are for sale, there may be a temporary wait on some parts as I have to wait until I have a stock part to replace it with. If you would like anything please send me a PM or post on here and I'll get in contact with you. Please serious offers...

On the back bumper of my 2014 jeep patriot is a little tiny piece about 1inch by 1 inch that is a door to a tow of some kind. The piece came off and it is driving me nuts. I want to replace it. Is this possible? See photo

Has anyone had luck finding any type of grill guard or bumper guard for their 2014 Jeep Patriot?

Hi, Joe here. I recently purchased a 2007 patriot 4x4 with 2.4 VVT and, 5 speed. I am also a welder and fabricator and am building a roof rack and bumpers for the patriot. These will be test units, and final version will be available for sale as soon as next month. The roof rack is similar to...

Just had some one scrap a 98 Ford F150 with a WAAG cattle guard on it and with a little work i think it could fit mint on my 2010 Riot. what do ya'll think?

Ive been on the forum for a while but this is my first thread. Ive got a 2007 jeep patriot trail rated. I have a custom off road bumper with a square stinger bar that i fabricated, a custom roof rack with four off road lights and an ax and shovel mount, RRO lift kit, falken wild peak 235/65/r17...

Trying to build a list of parts that I'll need for the conversion but having some trouble locating the part numbers. I'll post a list of the parts and when I get the numbers I'll update the list. Hopefully this will help anyone with the same goals. As of right now, we know that the bumper, and...

Has anyone looked into getting a tubular or pre-runner style bumper intended for a wrangler, and modifying it for the Patriot? The bumpers that are available are all too big and heavy for my liking. Any thoughts?

good morning my fellow jeep lovers! I am new to this community! But i had a question. i have a jeep patriot 2010 yesterday i scraped my underside on a curb and it took part of the plastic bumper. it was pretty far under my jeep and now a piece of metal is exposed. not sure if it's vital as...

Hi, recently got into an accident with my 2008 limited jeep patriot. Unfortunately the front bumper/grill and the metal bumper reinforcement have been damaged beyond repair. Radiator also needs replacing while the passenger side wing got slightly dented so i might need a new one also. Does...